602 Added Sta/Lta0 or Lta/Lta0 trigger parameter (see tsp.pdf) 601 Do not Use 600 Deeply tested for trigger to disk (Titan-FL) firmware. Many bugs fixed. Continuous TitanGps was making the disk flush to fail. Fixed. 507 Gps informations in informations frames 506 Flush times shorter, data loss during flushes should disapear. Flash writes optimisations. Tcs accepts 2*250 Hz or 2*160 Hz set of Fs. Fixed bug: Using Fat32 when 4GB or 8 GB (depending on disk capacity) was reached Titan was rejecting disk with "illegal bus scsi problem" reported. Fixed bug: Tcs was not able to set trigger parameters when a Titan3-FL was in use. 505- tests 504 Indexes are tagged with the msb channel number byte for Trigger to disk stations. Hard disk can cycle when full Minititan3-dg parameters loss. fixed. 503 When lowbat or disk full status was encountered, stations was locked as TITAN3. The only way to recover was to process a Titanrel. Fixed. 501 Continuous Flushes failed since 500. Fixed 500 Do not use! Trigger to disk mode 40E Some recent hard disks using recent IDE to Scsi adapters was not correctly managed by stations (holes in data). 40D Do not use 40C The problem concerning spurious sampling rate changes when using CS5321/23 Adcs is fixed. 40B Calibration pulses are now synchronized with primary samples within 1ms precision. 40A Offset correction is now always desactivated. Tcs and Seetitan Gps informations display bug fix. Tcs and Seetitan dysplay the current number of satellites if GPS connected and internal Titangps release >=4. 409 Serial number was not correctly broadcasted via Argos Link Xt or NT stations hung for 1 hour sometimes during telephone calls. 408 Local flush (using Tcs) was not working anymore. A PC Flush command (Atlas mode) can now require a clear data media Argos mode: Last Rx pulse milliseconds field was wrong (odd messages) 407 A bug when data retrieved was not laying on the same partition as writing fixed. 406 A bug when more than 1 hour of data retreiving on XT or NT stations. Fixed 405 Titanrel Ask for continuous DSP activity or not when run in non automatic mode. Latitudes and longitudes was prompted as unknown in TCS and Seetitan Gps.exe software prompts the internal GPS release. 404 The 3DG stations didn't save their parameters. fixed. 403 General Led blink period is very short when a Argos message is send. It stays in the state till the next send. A bugg in media amount of data displayed in TCS and SEETITAN is fixed. 30C modifications are included Cause to argos mode, the modem was not switched on when it rings. Fixed When internal software was <280 and TCS or SEETITAN >=280, some problems happened as "by 0 division". Fixed 402 401 First ARGOS mode release. 400 Don't include 30C modification Fat32 hard disk are supported. When a FAT32 hard disk is used, only one partition is defined The files triplet are repeated as DATA0, DATA0.NDX, DATA0.SIZ, DATA1, DATA1.NDX, DATA1.SIZ... JFMTTITAN is the java tool used to "titan-format" these hard disk. FAT16 previous specifications unchanged. Modem data retrieval ok for fat16 multi partition and FAT32 --------------------------------------------------------------- 30C: Fully operating release for the radio mode (spy mode with RTS/CTS handshake) 30B: When suitable EPROM in installed in, station accepts titanrel upload through a TitanGps Titanrel manage MINITITAN3DG target 30A Titanrel always ask for any target the sampling frequency family 309 TCS desactivates Uart's Fifo. Problems have been encountered on portable PCs. 308 Seetitan displays Geoscope slow channels 307 306 Tcs activate Uart's FIFO 305 304 Seetitan was not displaying correctly the full hard disk capacity. 303 GPS longitudes, latitudes and height was not correctly decoded when negative in Tcs and Seetitan 302 Seetitan had a 2K bugg. 301 Titanrel shows the TITAN3-G (as Geoscope) target 30 10/99 Hard disks with multi-partition are supported. The size of the partitions must be the same. Each partition must be a FAT16 one. FAT16 imposes the max size of hard disk to be less than 8 GB. Tcs allows a configuration file to be saved or loaded -------------------------------------------------------------------- 29.8 29.7 You can now choose a non automatic upload with titanrel and an automatic inetrnal EPROM. Hard disk that have more than 3 files are not rejected. The only 3 first files are taken into account. 29.6 New MINITITAN6 AND 6XT target in titanrel 29.5 29.4 29.3 Internal Eprom has station Serial number encoded in. 29.2 TCS and SEETITAN was repeating the A/D ligne in Infos window 29.1 29.0 Automatic titanrel upload. The station needs to have internal EPROM changed to take this functionality into account. Let you always try automatic upload. If it fails then the internal EPROM is not an automatic one.